ASTM F594 PDF

or visit us at ASTM F Scope – This specification covers the chemical and mechanical requirements for stainless steel. ASTM F specification covers chemical and mechanical requirements for stainless steel nuts in diameters ranging from 1/4″ to /2″. ASTM F covers seven groups of stainless steel alloys, including twelve austenitic, two ferritic, four martensitic and one precipitation hardening. BoltPort.

Author: Akisar Zolotaur
Country: Poland
Language: English (Spanish)
Genre: Literature
Published (Last): 16 September 2012
Pages: 144
PDF File Size: 2.56 Mb
ePub File Size: 5.64 Mb
ISBN: 284-9-55852-712-7
Downloads: 58362
Price: Free* [*Free Regsitration Required]
Uploader: Tojalabar

F When approved by the purchaser, alloys or Se may be furnished. Unless otherwise specified, all bolts, hex cap screws, and studs used with these nuts shall conform to the requirements of Specification F and shall be of the same alloy group. B legend of conditions: C The yield and tensile strength values for full size products shall be computed by dividing the yield and maximum tensile load value by the stress area for the product size and thread sizes determined in accordance with Test Methods F Condition AF – When Condition AF is specified, the ferritic alloys shall be annealed in accordance to same above condition A Ferritic Alloys after all cold working including heading and threading has been completed.

ASTM F – 09() Standard Specification for Stainless Steel Nuts

Seven groups of stainless steel alloys are covered, including ten austenitic, two ferritic, four martensitic, and one precipitation hardening: AF – Headed and rolled from annealed stock and then reannealed AH – Solution annealed and age hardened after forming.

A Unless otherwise specified on the inquiry and order, the choice of an alloy from within a group shall be at the discretion of the fastener manufacturer B See section 4. Link to Active This link will always route to the current Active version of the standard.

TOP Related Articles  ROBERTO ALCAZAR Y PEDRIN PDF

CW – Headed and rolled from annealed stock thus acquiring a degree of cold work. Condition AF – When Condition AF is specified, the austenitic alloys shall be annealed in accordance to Condition A after all cold working including heading and threading has been completed.

This abstract is a brief summary of the referenced standard. Referenced Documents purchase separately The documents listed below are referenced within the subject standard but are not provided as part of the standard. ASTM F covers seven groups of stainless steel alloys, including twelve austenitic, two ferritic, f94 martensitic and one precipitation hardening. E When approved by the purchaser, alloy F may be furnished.

Free Technical Information

A Tensile stress areas are computed using the following formula: The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. SH – Machined from strain hardened stock or cold worked to develop the specific properties. D Yield strength is the stress at which an offset of 0. AF – Headed and rolled from annealed stock and then reannealed AH – Solution annealed and age hardened after forming CW – Headed and rolled from annealed stock thus acquiring a degree of cold work.

ASTM F Specification – Boltport Fasteners LLP

A Minimum values except where shown as maximum or as a range. Condition CW – When Condition CW is specified, the ferritic alloys shall be annealed in accordance to above condition A for ferritic alloys, generally by the raw material manufacturer and atm cold worked to develop the specified properties.

TOP Related Articles  STEFFNY LAUFBUCH DOWNLOAD

The finished fasteners shall meet the applicable mechanical properties. Condition CW – When Condition CW is specified, the austenitic alloys shall be annealed zstm accordance with Condition A, generally by the raw material manufacturer and thenc old worked to develop the specified properties. Chemical tests; mechanical tests; and corrosion resistance shall be performed to conform with the specified requirements.

It is informational only and not an official part of the standard; the full text of the standard itself must be referred to for its use and application. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the f94 of regulatory limitations prior to use.

A – Machined from annealed or solution annealed stock thus retaining the properties of the original material; or hot formed and solution annealed. Historical Version s – view previous versions of standard.

This specification covers the requirements for stainless steel nuts in specified size, inclusive, in nominal diameter in a number of alloys in common use and intended for service applications requiring general corrosion resistance. ASTM does not give any warranty express or implied or make any representation that the contents asym this abstract are accurate, complete or up to date.